language
中国
韩国
韩国
韩国
韩国
韩国
021-54840828      shwpxl@126.com   
News
True core quality, focusing on R & D, manufacturing and service of wire and cable
Location:
Homepage
>
>
>
Double steel wire category 6 network cable elevator cable manufacturers take you to understand what to pay attention to when wiring the six types of network cables

Double steel wire category 6 network cable elevator cable manufacturers take you to understand what to pay attention to when wiring the six types of network cables

  • Categories:Industry news
  • Author:
  • Origin:
  • Time of issue:2022-03-18 16:57
  • Views:

(Summary description)Double steel wire category 6 network cable elevator cable manufacturers tell you that Category 6 wires are different from Category 5 and Category 5 used before in terms of construction and installation.

icon icon icon icon

Double steel wire category 6 network cable elevator cable manufacturers take you to understand what to pay attention to when wiring the six types of network cables

(Summary description)Double steel wire category 6 network cable elevator cable manufacturers tell you that Category 6 wires are different from Category 5 and Category 5 used before in terms of construction and installation.

  • Categories:Industry news
  • Author:
  • Origin:
  • Time of issue:2022-03-18 16:57
  • Views:
Information

Double steel wire category 6 network cable elevator cable manufacturers tell you that Category 6 wires are different from Category 5 and Category 5 used before in terms of construction and installation. The following Double steel wire category 6 network cable elevator cable manufacturers have sorted out a few points for you to pay attention to. Let's take a look at it.

Best Double steel wire category 6 network cable elevator cable Manufacturers china
1. Avoid overstretching
Double steel wire category 6 network cable elevator cable manufacturers tell you that the outer diameter of the Category 6 wire is thicker than that of the Category 5 wire. As for the box wire used for threading, some masters like to use brute force. If the thread cannot be pulled out, they will pull hard. In fact, it may just be stuck somewhere, and it can be taken out with a little pulling. Also, leave a certain amount of free length when wiring, taking into account possible future pulls. However, excessive pulling during wiring will deform the twisting pitch of the pair, which will seriously affect its anti-interference ability. It also significantly affects its structured return loss and impedance, resulting in a loss of overall return performance.
2. Avoid excessive bending and knotting
What if the line placement is wrong? Some masters will think that it would be good if you remove the cloth and fold it back again? Doing so will also distort the pitch of the pair. If it is bent too much, it will cause the pair to spread out directly, and it will also deform the cross skeleton, which will affect the pitch of the 4 pairs of twisted pairs, resulting in similar consequences to overstretching. Typically, the bend radius must not be less than 800% of the cable diameter, so redundant cables should not be too long. For Category 6 box lines, the bending radius should be greater than 50 mm. If the cable is kinked, it is directly regarded as damaged and should be replaced in time. Even if the master straightens the cable after tying the knot, it should be checked in time to confirm that there is no damage before using it again.
3. Avoid Compression
Double steel wire category 6 network cable elevator The cable manufacturer tells you that when wiring, the tightness of the crimping belt will deform the internal 4 pairs of twisted pairs, increase the return loss, and accumulate to make the total loss higher. Hooks or looped cable ties are recommended.
4. Pay attention to the weight
Category 6 wires are heavier than Category 5 wires. Double steel wire category 6 network cable elevator cable manufacturers tell you that you don't need to consider this when laying the ground wire, but you should pay attention to the weight when laying the suspension wire. When using suspension cables to support network cables, each suspension cable support point should not exceed 24 cables.
5. Reduce the length of parallel cables
I don't know if you have ever seen a scene where a large bundle of different wires are tied together? Double steel wire category 6 network cable elevator cable manufacturers tell you to try to avoid this situation. It is convenient to bundle different cables together in parallel, but the capacitive coupling of pairs of different cables with the same lay length will lead to a significant increase in crosstalk. This is called "alien crosstalk," and the best way to eliminate its adverse effects is to minimize the length of parallel cables.
6. Reduce coat peel length
The box wire is used for wiring, and an additional crystal head needs to be connected. The length of the outer skin cut when connecting the crystal head should be as small as possible. This can ensure that the laying distance of the internal pairs of the network cable is basically the same, and the return loss can be reduced.
The above is what the Double steel wire category 6 network cable elevator cable manufacturer tells you to pay attention to when wiring the Category 6 network cable. Hope it helps you.

Keyword:

Scan the QR code to read on your phone

Shanghai Wanpu Cable Co., Ltd.

Copyright ©  2020 Shanghai Wanpu Cable Co., Ltd. All rights reserved     沪ICP备17020559号